Lemur Pro (Parts & Repairs)

Many components in your Lemur Pro can be upgraded or replaced as necessary. Follow these step-by-step guides for instructions:

• Removing the bottom cover
• Replacing the RAM
• Replacing an M.2/NVMe SSD
• Replacing the WiFi/Bluetooth module
• Replacing the CMOS battery
• Replacing the fans/heatsink/thermal paste
• Replacing the speakers
• Replacing the main battery

Removing the bottom cover:

Removing the cover is required to access the internal components. Prior to removing the cover, ensure the AC power is unplugged and all peripherals (including SD cards and USB drives) are unplugged or removed from the system.

Tools required: Cross-head (Phillips) screwdriver
Time estimate: 5 minutes
Difficulty: Easy ●
Screws: 12 total

Steps to remove the bottom cover:

1. Place the machine lid-side down.
   • Use a soft surface (such as a towel) to avoid scratches.
2. Remove the 12 screws from the bottom panel.

3. Lift the bottom cover off, starting from the hinges in the back.

Replacing the RAM:

The Lemur Pro 11 comes with 8GB of 3200 MHz RAM soldered onto the motherboard, which cannot be replaced. There is an additional RAM slot, which can support up to a 32GB stick for 40GB of RAM total. The additional stick is a standard DDR4 SO-DIMM running at 3200 MHz.

Tools required: Cross-head (Phillips) screwdriver
Time estimate: 10 minutes
Difficulty: Easy ●

Steps to replace the RAM:

1. Follow the steps above to remove the bottom cover.
2. Press the small tabs on both sides of the RAM simultaneously. The RAM should spring up to an angle.

3. Remove the RAM from the slot.
4. Insert the new RAM (or reseat the existing RAM) by placing it into the keyed slot and pressing down until it clicks into place.

Replacing an M.2/NVMe SSD:

This model supports two M.2 SSDs. Both slots are size 2280. SSD-1 supports PCIe NVMe Generation 3 or SATA III, while SSD-2 supports PCIe NVMe Generation 4.

Tools required: Cross-head (Phillips) screwdriver
Time estimate: 10 minutes
Difficulty: Easy ●

Steps to replace the M.2 drive:

1. Follow the steps above to remove the bottom cover.
2. Unscrew the retainer screw opposite the M.2 slot.
   • SSD-1 is between the battery and the speaker.
   • SSD-2 is next to the RAM slot.

3. Remove the existing M.2 drive by pulling it out of the slot.
4. Insert the new M.2 drive into the slot and hold it down.
5. Replace the retainer screw.

Replacing the wireless card:

Your system's WiFi and Bluetooth are both handled by the same module. It connects with a standard M.2 2230 slot with PCIe and USB interfaces (E-key).

Tools required: Cross-head (Phillips) screwdriver
Time estimate: 10 minutes
Difficulty: Medium ●

Steps to replace the WiFi/Bluetooth module:

1. Follow the steps above to remove the bottom cover.
2. Locate the wireless card (next to the CPU fan.) Remove any clear tape that is securing the wires.

3. Gently remove the two antennas (highlighted red above) by pulling them up and away from the wireless card.
4. Remove the retaining screw opposite the M.2 slot, highlighted yellow above.
5. The wireless card will pop up at an angle. Remove the card from the M.2 slot.
6. Insert the new wireless card into the M.2 slot at an angle.
7. Replace the retaining screw.
8. Attach the two antennas by aligning the circular fittings and pressing onto the wireless card. The connectors will snap into place. Use caution when attaching the connectors; the pins can bend, break, or snap.

Replacing the CMOS battery:

The CMOS battery supplies power to the system's CMOS chip. UEFI settings and the computer's hardware clock are stored on the CMOS. If your system doesn't boot, you can reset the CMOS to force a low-level hardware reset. If your clock is constantly resetting, it's likely your CMOS battery needs to be replaced.

Tools required: Cross-head (Phillips) screwdriver
Time estimate: 10 minutes
Difficulty: Medium ●

Steps to replace the CMOS battery:

1. Follow the steps above to remove the bottom cover.
2. Follow the steps above to remove the primary SSD.
3. Remove any clear tape that is securing the battery, then pull the battery away from the adhesive holding it to the case.
   • If you are only clearing the CMOS and are not replacing the CMOS battery, removing the SSD and CMOS battery is optional, but will make it easier to unplug the CMOS battery connector.

4. Unplug the white connector attaching the CMOS battery to the motherboard.
5. To clear the CMOS, disconnect the main battery, open the lid of the machine, and hold down the power button for at least 15 seconds to discharge any residual energy in the system.
6. Re-connect the CMOS battery and the main battery, and replace the SSD and bottom panel.
7. Power up the machine. The system may power itself off and on after initial boot; this is normal behavior when the CMOS has been reset.

Replacing the cooling system:

If the CPU fan becomes noisy and cleaning it out doesn't fix the issue, you may need a new CPU fan. Contact support to start a warranty claim or parts purchase.

Depending on your climate and the age of the machine, it may be necessary to apply new thermal paste between the CPU and the heatsink. Thermal paste helps facilitate effective heat transfer between the CPU and the cooling equipment. These instructions can also be used in the unlikely event your heatsink needs to be replaced.

Tools required: Cross-head (Phillips) screwdriver
Time estimate: 20 minutes
Difficulty: High ●

Steps to replace the fans/heatsink/thermal paste:

1. Follow the steps above to remove the bottom cover.
2. Disconnect the small connector plugging the fan into the motherboard, highlighted yellow below.
   • This can alternatively be done after the fan/heatsink is removed.

4. Remove the two fan screws (highlighted cyan above) and any clear tape holding the fan in place.
5. Remove the heatsink screws in reverse order, starting with #3, then #2, and finally #1.
6. Remove the heatsink/fan from the system, being careful not to bend the heatsink pipe. It may take some pressure to break the seal of the thermal paste.
7. Using a paper towel, remove the existing thermal paste. You may also use a small amount of rubbing alcohol to remove excess or difficult-to-remove paste.

8. After cleaning the CPU and heatsink, apply a small line of thermal paste directly onto the CPU.

9. Carefully replace the fan and heatsink.
10. Replace the heatsink screws, starting with #1, then #2, and finally #3.
11. Replace the fan screws and plug the fan back in.
    • When plugging the fan in, the black wire goes on the left (closest to the side of the machine.)

Replacing the speakers:

The system has two bottom-firing speakers, which can be removed and replaced individually.

Tools required: Cross-head (Phillips) screwdriver
Time estimate: 10 minutes
Difficulty: Medium ●

Steps to replace the speakers:

1. Follow the steps above to remove the bottom cover.
2. Disconnect the speaker wire from the motherboard.
   • This can alternatively be done after freeing the speaker.

3. Pull the tops of the purple rubber circles over the black tabs holding them in place.
4. Lift the speaker up and off of the plastic posts.

5. Slide the new speaker onto the plastic posts and connect it to the motherboard.

Replacing the main battery:

The battery provides primary power whenever the system is unplugged.

The model number for the Lemur Pro 11's battery is L140BAT-4, and the original part number is 6-87-L140S-72B01. Third-party battery sellers may list one or both of these numbers, and may offer other compatible part numbers with the same model number. You can also contact System76 to purchase a replacement battery.

CAUTION: Do not use metal tools to remove the battery. Do not touch the battery contacts with your hands or metal objects. If the battery is damaged during repairs, do not reinsert it into the laptop. Do not continue to use the computer if it contains a damaged battery. It is a potential fire hazard to operate a computer with a damaged battery. Keep children away from, and properly dispose of, the damaged battery. Always dispose of batteries carefully, by placing a piece of tape on the contact points. Take damaged batteries to an electronics recycling center and contact System76 to purchase a replacement. Batteries may explode or leak if exposed to fire, or if improperly handled or discarded. Only use batteries designed for your specific computer. This product contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal.

Tools required: Cross-head (Phillips) screwdriver
Time estimate: 30 minutes
Difficulty: High ●

Steps to replace the main battery:

1. Follow the steps above to remove the bottom cover.
2. Unplug the white connector that connects the battery to the motherboard.

3. Remove the battery.
   • The battery is secured to foam standoffs with double-sided tape.
   • A flat plastic object (such as a credit card) can be used to separate the tape from the battery.
   • If any tabs from the tape are visible around the perimeter of the battery, do not push them back under the battery.
     • Hold the tabs down while inserting the plastic tool to separate the tape and foam from the battery.
     • Alternatively, pull the tabs up with the battery to separate the tape and foam from the chassis.
4. Put the battery back (or put your new battery in its place) and plug it back into the motherboard.